Gbox klient a oscam server

[slon]

Prepojenie GBOX klienta s OSCAM serverom:
- klient (tank1) - prijimac COOLSTEAM TANK s image NG-Return 3.0, GBOXNET (gbox.net 2.2A 807E Aug 10 2013 145816 mt, verzia gbox.arm.lnxlib, premenovany na gbox), v hornej citacke RTVS karta, v dolnej SKYLINK ICE karta
- server (asus) - router ASUS RT-N16 s DDWRT, OSCAM 10896, ziadna interna citacka, len proxy newcamd a cs357x
Pre klienta momentalne nie je funkcny cs2gbox (pravdepodobne otazka kniznic), takze prepojenie je cez gbox protokol.
Nastavenie klienta:
- gbox_cfg
Z: { 01 12 } tank1 8024
G: { 03 }
C: { 01 }
M: { 01 }
A: { 01 }
U: { 01 }
H: { 01 }
T: { 00 }
O: { 00 } tank1 coolstream
L: { 00 } tank1 7025
V: { F0 30 }
F: { 08 } 1

- cwshare.cfg
I: { 06 }
N: { 00 01 03 2F 4000 6000 }
X: { 0A }
M: { tank1 { A123BCDE }}
D: { asus { 11114 11115 { 98AF3E20 { A3 A3 }}}}

Nastavenie servera:
- oscam.conf
[gbox]
port = 11115
hostname = asus
my_password = 98AF3E20

[reader]
label = gbox_tank1
protocol = gbox
device = tank1,11114
user = xxx
password = A123BCDE
gbox_max_distance = 9
gbox_max_ecm_send = 9
group = 1
cccreshare = 9
ccchop = 9
audisabled = 1

Uzivatel (user) xxx musi existovat v oscam.user s prislusnou skupinou (group). Toto je standardne prepojenie GBOXu a OSCAMu, klient sa aj spoji so serverom, ale data zo servera - newcamd citaciek nedostane. Zo zdrojovych kodov oscamu sa da zistit, ze gbox potrebuje internu citacku alebo proxy cccam citacku na oscame. Dalsi krok je vytvorenie cccam citacky a spustenie cccam protokolu, bude to fungovat tak, ze citacka sa pripoji na protokol len v ramci servera, ale vyuzivana nebude, lebo bude mat nikde nepouzitu skupinu (group).

- oscam.conf
[cccam]
port = 11116
nodeid = F44018C210D41526
version = 2.3.0
reshare = 1
stealth = 1
recv_timeout = 6000

Nodeid je mozne pouzit defaultne, to ktore ponukne sam OSCAM, ked sa pridava cccam protokol cez webove rozhranie.

- oscam.server
[reader]
label = cccam_asus
protocol = cccam
device = asus,11116
user = yyy
password = password
inactivitytimeout = 30
group = 10
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
cccversion = 2.3.0
cccwantemu = 1
ccckeepalive = 1
cccreshare = 1
audisabled = 1

Uzivatel (user) local musi existovat v oscam.user s prislusnou skupinou (group), a heslom. Po restarte oscam vytvori citacku cccam_asus, pripojenu na cccam protokol a virtualne karty podla caid.
Po restarte GBOXu uz klient bude dostavat data z newcamd citaciek. GBOX vyborne manipuluje s kartami klienta, prepina podla dostupnych zapisov a rychlosti odozvy, takze RTVS karta dostava prednost pre SKYLINK ICE pri JEDNOTKE a DVOJKE, lebo SKYLINK ICE bezi na CRYPTOWORKS a odozvu ma mierne vyssiu ako RTVS IRDETO karta. Ked z nejakeho dovodu zlyha RTVS karta, GBOX automaticky prepne na SKYLINK bez prerusenia dekodovania. Zapisy na obe karty funguju spravne.

[ahojj]

Caute, nemôžem nakonfigurovať gbox v Enigma 2 Infinity(klient) na HDbox9105 Plus a oscam(server) original soft na HDbox9105
V klientovi mám:
- gbox_cfg
Z: { 01 12 } IP_PC 8024
G: { 03 }
C: { 01 }
M: { 01 }
A: { 01 }
U: { 01 }
H: { 01 }
T: { 00 }
O: { 00 } IP_boxu (sluzi na zobrazovanie informacii na OSD boxu)
L: { 00 } IP_boxu 7025
V: { F0 30 }
F: { 08 } 1

- cwshare.cfg
M: { IPklient { hdbox3 }}
D: { IPserver { 11114 11115 { hddbox {A3 A3}}}} (posiela karty na daslie 3 urovne)
I: { 06 }
N: { 00 01 03 2F 4000 6000 }
X: { 0A }

Na serveri mám tieto údaje(config):
-oscam.conf
[gbox]
hostname = IPserver
port = 11115
my_password = hddbox

[cccam]
port = 11116
nodeid = E8FBCF1B107D158E
version = 2.3.0
reshare = 1
stealth = 1
recv_timeout = 6000

-oscam.user
[account]
user = hdbox1
pwd = hdbox1
keepalive = 1
group = 10

[account]
user = hdbox3
pwd = hdbox3
group = 1

[account]
user = hddbox
pwd = hddbox
group = 1

-oscam.server
[reader]
label = CCcam
enable = 1
protocol = cccam
device = IPserver,11116
user = hdbox1
password = hdbox1
inactivitytimeout = 30
group = 10
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
cccversion = 2.3.0
cccwantemu = 1
ccckeepalive = 1
cccreshare = 1
audisabled = 1

[reader]
label = GBox
protocol = gbox
device = IPklient,11114
user = hdbox3
password = hdbox3
gbox_max_distance = 9
gbox_max_ecm_send = 9
group = 1
cccreshare = 9
ccchop = 9
audisabled = 1

Na klientovi mám tieto údaje(config):
-oscam.user
[account]
user = hdbox3
pwd = hdbox3
group = 1
-oscam.server
[reader]
label = CCCamgbox
protocol = cccam
device = IPserver,11116
user = hdbox2
password = hdbox2
inactivitytimeout = 30
group = 1
blockemm-unknown = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
cccversion = 2.3.0
cccwantemu = 1
ccckeepalive = 1
cccreshare = 1
audisabled = 1

[reader]
label = GBOx
enable = 0
protocol = gbox
device = IPklient,11114
user = hdbox3
password = hdbox3
gbox_max_distance = 9
gbox_max_ecm_send = 9
group = 1
cccreshare = 9
ccchop = 9
audisabled = 1

[ahojj]

co je na tom zle? mohli by ste mi to opravit a vysvetlit preco? to IP_PC ktoreho PC tam mam dat a preco PC ked ty tam mas tank1 cize klient? IP_boxu mam dat ktoreho? servera alebo klienta? ostatne je dobre? lebo aj tak mi to nejdem to co si mi opravil cervenym

[EnoSat]

co je na tom zle? mohli by ste mi to opravit a vysvetlit preco? to IP_PC ktoreho PC tam mam dat a preco PC ked ty tam mas tank1 cize klient? IP_boxu mam dat ktoreho? servera alebo klienta? ostatne je dobre? lebo aj tak mi to nejdem to co si mi opravil cervenym

pretoze na tom porte posiela debug prace do PC (mohol by si dat aj IP boxu ak by si mal sputeny plugin gbox suite)

ale ked spojis cccam protokol s gbox protokolom tak vecsina oscamov zblbne

[ahojj]

okej vďaka takze mi to nepojde?

[EnoSat]

okej vďaka takze mi to nepojde?

pojde , ale zalezi ako si budu verzie navzajom "rozumiet"

[purko]

Ktory cs2gbox použijem na zdielanie medzi dvoma Trinity

[EnoSat]

Ktory cs2gbox použijem na zdielanie medzi dvoma Trinity

cs2gbox nezdiela , len preklada newcamd protokol do gbox protokolu