Kód: Vybrat vše
batch ............. Load a batch file into memory and execute it
boards ............ Show supported boardsKód: Vybrat vše
boot .............. Load an executable file into memory and execute it
boot emmcflash0.kernel_1 'root=/dev/mmcblk0p5 rw rootwait rootflags=data=journal debug coherent_pool=2M brcm_cma=504M@0x10000000 brcm_cma=260M@0x2f800000 brcm_cma=1024M@0x80000000'
boot emmcflash0.kernel_2 'root=/dev/mmcblk0p7 rw rootwait rootflags=data=journal debug coherent_pool=2M brcm_cma=504M@0x10000000 brcm_cma=260M@0x2f800000 brcm_cma=1024M@0x80000000'
boot emmcflash0.kernel_3 'root=/dev/mmcblk0p9 rw rootwait rootflags=data=journal debug coherent_pool=2M brcm_cma=504M@0x10000000 brcm_cma=260M@0x2f800000 brcm_cma=1024M@0x80000000'
boot emmcflash0.kernel_4 'root=/dev/mmcblk0p11 rw rootwait rootflags=data=journal debug coherent_pool=2M brcm_cma=504M@0x10000000 brcm_cma=260M@0x2f800000 brcm_cma=1024M@0x80000000'
boot emmcflash0.kernel1 'root=/dev/mmcblk1p3 rootfstype=ext4 rootwait'
Kód: Vybrat vše
crc ............... Report the CRC32 for a memory range.
d ................. Dump memory.
dir ............... List the directory of a FAT file system
dt on ............. (Re-)enable the silent 'dt bolt' command that happens just before the 'boot' command executes.
dt off ............ Disable the silent 'dt bolt' command that happens just before the 'boot' command executes.
dt bolt ........... Modify an existing DTB with an autogenerated BOLT config.
The DT_ADDRESS envar is used as the base address of the dtb.
dt memreserve ..... Add an entry to the DTB memory reservation table.
The address and length shall be specified in hex.
The DT_ADDRESS envar is used as the base address of the dtb.
dt del prop ....... Delete a property from the DTB. The DT_ADDRESS envar is used as the base address of the dtb.
dt del node ....... Delete a node from the DTB. The DT_ADDRESS envar is used as the base address of the dtb.
dt add prop ....... Add a new property to the DTB. The DT_ADDRESS envar is used as the base address of the dtb.
dt add node ....... Add a new node to the DTB. The DT_ADDRESS envar is used as the base address of the dtb.
dt sane ........... Check DTB header. The DT_ADDRESS envar is used as the base address of the dtb.
dt show ........... Decode contents of a memory resident DTB file as a DTS.
The DT_ADDRESS envar is used as the base address of the dtb.
e ................. Modify contents of memory.Kód: Vybrat vše
ephycfg ........... Configure Ethernet PHY interface
BOLT> ephycfg -e
1) MII to external 10/100Mbps PHY (e.g. bcm53101E) on GENET_0
2) RGMII ID mode disabled for external 10/100/1000Mbps PHY (e.g. bcm5461x) on GENET_0
3) RGMII to external Gigabit Switch (e.g. bcm531x5) on GENET_0
4) RGMII ID mode disabled for external Gigabit Switch on GENET_0
5) RGMII to RGMII (e.g. STB<->3383) on GENET_0
6) Internal GPHY (built-in PHY) on GENET_0 (defaults)
Selection:Kód: Vybrat vše
erase ............. Erase flash device or partition
f ................. Fill contents of memory.
flash ............. Update a flash memory device
gisb .............. Show or set GISB bus timeout
go ................ Start a previously loaded program.Kód: Vybrat vše
help .............. Obtain help for BOLT commands
BOLT> help help
SUMMARY
Obtain help for BOLT commands
USAGE
help [command]
Without any parameters, the 'help' command will display a summary
of available commands. For more details on a command, type 'help'
and the command name.
*** command status = 0Kód: Vybrat vše
ifconfig .......... Configure the Ethernet interface
BOLT> ifconfig eth0 -auto
100 Mbps Full-Duplex
Device eth0: hwaddr 00-11-22-33-44-55, ipaddr 192.168.1.210, mask 255.255.255.0
gateway 192.168.1.1, nameserver 192.168.1.1
DHCP server 192.168.1.1, DHCP server MAC AA-BB-CC-DD-EE-FF
*** command status = 0
Kód: Vybrat vše
incenv ............ Increment an integer environment variable.Kód: Vybrat vše
info .............. Show BOLT configuration information
BOLT> info
========================================================================
CPU speed: 1503MHz
DDR0 Frequency: 1067MHz, 4Gx16 phy:3240000000 @ 00000000
DDR1 Frequency: 1067MHz, 4Gx16 phy:3240000000 @ 80000000
Total memory: 2048MB
Boot Device: SPI
SDIO:
controller 0, TYPE: SD
controller 1, TYPE: EMMC
BSP version: '2.1.0'
Total memory used by BOLT: 0x070080E0 - 0x0708EBF8 (551704)
Initialized Data: 0x07033000 - 0x07077170 (278896)
BSS Area: 0x07077170 - 0x0708EBF8 (96904)
Local Heap: 0x07100000 - 0x09100000 (33554432)
Stack Area: 0x09100000 - 0x09200000 (1048576)
Text (code) segment: 0x070080E0 - 0x07012CA8 (43976)
FSBL info area: 0x06FFC000 - 0x06FFC044 (68)
Page table base: 0x07000000
BOLT driver build information:
LDR: ELF 1; RAW 1; SREC 1; ZIMG 1
UI: LEVEL 3; MIN 0
FS: FAT 1; FAT32 1
NET: STACK 1; ENET 1; TCP 1
USB: STACK 1; ETH 1; DISK 1; SERIAL 1; HID 1
FLASH: NAND
SPLASH: 1048576; emmcflash0.splash
========================================================================
*** command status = 0Kód: Vybrat vše
load .............. Load an executable file into memory without executing it
loop .............. Loop a commandKód: Vybrat vše
macprog ........... Program the MAC address.
BOLT> macprog 00-11-22-33-44-55
Programming flash...done
*** command status = 0Kód: Vybrat vše
memtest ........... Test memory.
memwrap ........... Test for end of (ddr) memory.
The -ddr option pre-fills -base & -top values, which may be overridden by your own (option.) -base & -top.
mii ............... Reads or writes register contents from/to specified PHY address on a given MDIO bus
(use show devices to discover the bus).
ping .............. Ping a remote IP host.Kód: Vybrat vše
printenv .......... Display the environment variables
BOLT> printenv
Variable Name Value
-------------------- --------------------------------------------------
BOOT_CONSOLE uart0
SPLASH ENABLE
STARTUP batch -fatfs emmcflash0.startup:STARTUP
VERSION 9.99
CHIP_FAMILY_ID 73660020
BOARDNAME BCM97366SFF_bad_MoCA
MEMORYSIZE 2048
DT_ADDRESS 761c000
DT_SIZE a2c7
ETH0_PHY INT
ETH0_MDIO_MODE 1
ETH0_SPEED 1000
ETH0_PHYADDR 1
DRAM0_SIZE 1024
DRAM1_SIZE 1024
ETH0_HWADDR 00:11:22:33:44:55
*** command status = 0Kód: Vybrat vše
reboot ............ Reboot the system
rlogin ............ Mini rlogin client.
rpmb counter ...... Read the RPMB Write Counter.
rpmb program-key .. Program the authentication key.
rpmb use-key ...... Specify the key to be used for all RPMB operations.
rts ............... List all, or select an rts
save .............. Save a region of memory to a remote file via TFTP
set console ....... Change the active console device
setboard .......... Set board number
setenv ............ Set an environment variable.Kód: Vybrat vše
show usb .......... Display devices connected to USB bus.
BOLT> show usb
Bus 0 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 1 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 2 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 3 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 4 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 4 Device 2 Class 0 Vendor 148F Product 5372 [DEVICE]
Bus 5 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 6 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
Bus 7 Device 1 Class 9 Vendor 0000 Product 0000 [HUB]
*** command status = 0Kód: Vybrat vše
show heap ......... Display information about BOLT's heapKód: Vybrat vše
show devices ...... Display information about the installed devices.
BOLT> show devices
Device Name Description
------------------- ---------------------------------------------------------
uart0 16550 DUART at 0xf040b000 channel 0
mem0 Memory
emmcflash0 EMMC flash Data : 0x000000000-0x0E9000000 (3728MB)
emmcflash0.startup EMMC flash Data : 0x000400000-0x000500000 (1024KB)
emmcflash0.initrd EMMC flash Data : 0x000500000-0x001100000 (12MB)
emmcflash0.splash EMMC flash Data : 0x001100000-0x001300000 (2048KB)
emmcflash0.kernel_1 EMMC flash Data : 0x001300000-0x001900000 (6MB)
emmcflash0.rootfs_1 EMMC flash Data : 0x001900000-0x03B200000 (921MB)
emmcflash0.kernel_2 EMMC flash Data : 0x03B200000-0x03B800000 (6MB)
emmcflash0.rootfs_2 EMMC flash Data : 0x03B800000-0x075100000 (921MB)
emmcflash0.kernel_3 EMMC flash Data : 0x075100000-0x075700000 (6MB)
emmcflash0.rootfs_3 EMMC flash Data : 0x075700000-0x0AF000000 (921MB)
emmcflash0.kernel_4 EMMC flash Data : 0x0AF000000-0x0AF600000 (6MB)
emmcflash0.rootfs_4 EMMC flash Data : 0x0AF600000-0x0E8F00000 (921MB)
emmcflash1 EMMC flash Boot1: 0x000000000-0x000400000 (4MB)
emmcflash2 EMMC flash Boot2: 0x000000000-0x000400000 (4MB)
emmcflash3 EMMC flash RPMB : 0x000000000-0x000080000 (512KB)
flash0.bolt SPI flash @ CS0: 0x00000000-0x00200000 (2048KB)
flash0.macadr SPI flash @ CS0: 0x00200000-0x00210000 (64KB)
flash0.nvram SPI flash @ CS0: 0x00210000-0x00220000 (64KB)
flash0.devtree SPI flash @ CS0: 0x00220000-0x00230000 (64KB)
flash0 SPI flash @ CS0: 0x00000000-0x00400000 (4MB)
eth0 GENET Internal Ethernet at 0xf0b60000
mdio0 GENET MDIO at 0xf0b60800
sata0 SATA3 AHCI Device
sata1 SATA3 AHCI Device
uart_b0 16550 DUART B at 0xf040b040 channel 0
*** command status = 0Kód: Vybrat vše
sleep ............. Sleep for specified milliseconds.
t ................. Test contents of memory.
tcp constest ...... Tcp console test.
tcp listen ........ Port listener.
tcp connect ....... TCP connection test.
testenv ........... Tests environment variable for various conditions.
The default is to test the existence of the
variable.
ttcp .............. TCP test command.
u ................. Disassemble instructions.
uncache ........... Mark (all ddr) memory access via the mmu as uncached. Effects vary depending upon the architecture.
unsetenv .......... Delete an environment variable.
usb exit .......... Stop & reset the USB controller.
usb init .......... Initialize the USB controller.
waitusb ........... Wait for USB device to be installed.Kód: Vybrat vše
BOLT> dir usbdisk0
*** Sony Storage Media (3900 MB, lbs=512) ***
11648128 RLDM.bin
*** command status = 0
BOLT> boot usbdisk0:/RLDM.bin