Stránka 2 z 5
Re: Veli pomale prepinanie medzi programami
Napsal: 02.březen 2019 - 18:49
od vado
@mtester270
nemyslim, ze tu varim z vody, preco si to myslis ?
Tu mas vypis zo syslogu, ktory som tu uz pastol. Velmi rad Ti podakujem za Tvoj navod, ako mam dalej postupovat.
Feb 25 21:19:39 vuduo4k user.warn kernel: [ 3522.549771] FE tune fe_handle=c67ad800
Feb 25 21:19:41 vuduo4k user.warn kernel: [ 3524.878768] FE tune fe_handle=c67ad800
Feb 25 21:19:43 vuduo4k user.warn kernel: [ 3527.117764] FE tune fe_handle=c67ad800
---------------------------------------------------
Problem vyzera byt v nizsej citlivoti tunerov - neschopnosti sa nasynchronizovat na dany kanal - VU+4k.
Doladil som polohu paraboly vo V aj H smere, polohu LNB, vymenil som F-konektory.
Prepinanie programov sa zrychlilo, ale v porovnani so starym VU+ DUO je to stale nepostacujuce.
Moj osobny nazor je, ze citlivost (mozno len toho konkretneho kusa tuneroveho modulu, ktory mam ja) je ovela nizsia, ako citlivost tunera v starom VU+ DUO, alebo to z nejakeho (neviem akeho) duovodu trva dlho, pokial tuner dokaze "nasynchronizovat" na prave spracovavany signal.
vado
Re: Veli pomale prepinanie medzi programami
Napsal: 02.březen 2019 - 19:23
od EnoSat
FrontEnd naladil a spracovava c67ad800
chod za predajcom alebo do servisu vymen tuner
Re: Veli pomale prepinanie medzi programami
Napsal: 02.březen 2019 - 20:08
od vado
@enosat
Dakujem za radu.
Vado
Re: Veli pomale prepinanie medzi programami
Napsal: 17.březen 2019 - 0:55
od vado
Vyriesene.
Je nutne nastavit pre kazdy transponder DVB-S2 parameter PILOT na OFF, alebo ON. Pokial je tento parameter nastaveny na AUTO, tak to robi prave tieto mnou popisovane problemy.
Aktualne: prepinanie kryptovanych programov 1-2 sekundy. Nekodovane pod 1 sekundu.
vado
Re: Veli pomale prepinanie medzi programami
Napsal: 17.březen 2019 - 19:50
od dano01
...... každý transpondér DVB-S2 parameter PILOT nastavený na AUTO a nie sú žiadne problémy s prepínaním programov, prepnutie trvá 1-2 sec, mám VU SOLO-2, a fw BH......
Re: Veli pomale prepinanie medzi programami
Napsal: 17.březen 2019 - 20:03
od VTronik
Že to chodí dobře na Solu2 ještě neznamená, že to stejně dobře chodí na Duo 4K...
Re: Veli pomale prepinanie medzi programami
Napsal: 18.březen 2019 - 16:53
od kix
mne to blbne na zero 4k, prejavuje sa to tak, ze ked prepinam, tak par programov za sebou prepne rychlo a potom dalsi kanal trva dlho kym sa zobrazi obraz, prepnem naspat na ten predchadzajuci a znova dam dopredu na ten isty kanal a uz to ide ako ma. Takze robi to nahodne. Nepomohlo ani nastavit pilot na ine ako auto. Ja upodozrievam oscam, kde mam home share skylink irdeto karty, ze tam je pes zakopany. Ze to robi newcamd klient. To sa da najst aj na inych forach.
Re: Veli pomale prepinanie medzi programami
Napsal: 18.březen 2019 - 17:38
od vado
Ahoj,
mne to robilo spozdenie aj pri prepinani medzi FTA, napriklad CT24 a TA3. OSCAM v tom asi nebude.
Je mozne, ze za to moze stary (12+ rokov) LNB + tiez rovnako stara kabelaz. Alebo problem s tunerom (HW ?). VU+ DUO2 na tej istej kabelazi problem nema.
Zaujimave je, ze na vsetkych programoch, ked uz sa tam VU prepne (nezalezi na tom, ci hned, alebo az o 5 sekund), mam hodnoty signalu na urovni 85 a viac %. Ale tie sa ukazu az prave po tych 5 sekundach. Akokeby tuner skusal kazde nastavenie PILOT az do momentu, ked sa trafi (len nahlas rozmyslam).
V kazdom pripade, odkedy som nastavil PILOT rucne, nemam problem.
Re: Veli pomale prepinanie medzi programami
Napsal: 18.březen 2019 - 19:20
od siem
Mne to robilo rovnako problém, niektoré stanice po prepnutí na ne ukazovali pár sekúnd úroveň signálu 0% a až potom naskočil signál . dnes som cez DreamboxEdit stiahol do PC setting, nastavil som na jednom transponderi Pilot ON namiesto AUTO odoslal na VU+ a odvtedy všetko prepína ako má bez akéhokoľvek oneskorenia. Neviem prečo je to tak, ale funguje to.
Re: Veli pomale prepinanie medzi programami
Napsal: 12.leden 2021 - 8:29
od flubertn
Zdravim. Prechadzal som 1w na 23,5 a takisto mi zacali niektore programy nabiehat pomaly. Kde presne sa da zmenit ten PILOT on off pri jednotlivich transpondentoch. V STB ani DreamboxEDIT sa mi to nepodarilo najist.
Re: Veli pomale prepinanie medzi programami
Napsal: 12.leden 2021 - 8:59
od vado
Neviem, aky mas prijimac, ale vo VU+4k s BH sa to nastavuje cez DO postupom:
menu -> Nastavenie -> Vyhladavanie stanic -> Rucne vyhladavanie
Takto sa dostanes ka nastaveniu aktuale prijimaneho transpondera.
Tam prejdes na polozku "Pilot" a nastavis podla potreby.
Vado
Re: Veli pomale prepinanie medzi programami
Napsal: 12.leden 2021 - 10:26
od siem
Ide to aj pomocou DreamboxEdit.
Stačí kliknúť na stanicu pravým tlačítkom myši a v menu sa objaví aj položka : "Udaje o transpondéru " a tam sa dá nastaviť aj Pilot Off/On . Nastavenie platí pre všetky kanály transpondéra.
Re: Veli pomale prepinanie medzi programami
Napsal: 12.leden 2021 - 20:33
od flubertn
Ďakujem. Pomohlo. Upravil som cez Dreambox u všetkých TP ktoré používam a svišťí to ako hodinky. Taká blbosť....
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 12:31
od dipol100
Na novém Duo4KSE mám problém s pomalým přepínáním v DVB-T2, signál chytám z vysílače Buková hora, ze kterého chytám na kanále 33 programy ČT, na kanále 31 Novu a na kanále 38 Primu. Pokud přepínám postupně CT1, ČT2, Nova, Nova Cinema, Prima je prodlev kolem 1-2 sec, ale jakmile chci skočit z TV Prima rovnou na ČT1, tak je prodleva i 30 až skoro 180 sekund. Zlobí to jen při skoku na programy ČT, níže část logu, mělo by to tam být vidět, já se v tom ale nevyznám, může nějaká dobrá duše (která tomu rozumí) zjistit, jestli je to problém image (OATV 6.4), nebo je problém s tunerem, nebo dokonce s přijímačem? Signál mám kolem 95% a GigaBlue QUAD 4K s tím nemá sebemenší problém. Už jsem z toho zoufalej.
Kód: Vybrat vše
12:04:46.1274 [ ] dvb/cahandler.cpp:497 ~eDVBCAService [eDVBCAService] free service 1:0:1F:312:F206:20CB:EEEE0000:0:0:0::Prima HD T
12:04:46.1336 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.1339 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.1355 [ ] dvb/decoder.cpp:870 setState [eTSMPEGDecoder] decoder state: play, vpid=ffffffff, apid=ffffffff
12:04:46.1355 < > dvb/decoder.cpp:762 stop [eDVBPCR0] DEMUX_STOP ok
12:04:46.1356 [ ] dvb/decoder.cpp:773 ~eDVBPCR [eDVBPCR0] destroy
12:04:46.1356 < > dvb/decoder.cpp:431 stop [eDVBVideo0] DEMUX_STOP ok
12:04:46.1366 < > dvb/decoder.cpp:440 stop [eDVBVideo0] VIDEO_STOP ok
12:04:46.1400 [ ] dvb/decoder.cpp:532 ~eDVBVideo [eDVBVideo0] destroy
12:04:46.1401 < > dvb/decoder.cpp:163 stop [eDVBAudio0] AUDIO_STOP ok
12:04:46.1678 < > dvb/decoder.cpp:171 stop [eDVBAudio0] DEMUX_STOP ok
12:04:46.1679 < > dvb/decoder.cpp:207 unfreeze [eDVBAudio0] AUDIO_CONTINUE ok
12:04:46.1769 [ ] dvb/decoder.cpp:251 ~eDVBAudio [eDVBAudio0] destroy
12:04:46.1782 [ ] dvb/dvb.cpp:1497 DVBChannelStateChanged [eDVBResourceManager] start release channel timer
12:04:46.1893 { E } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] setPixmapNum(0) failed! defined pixmaps: []
12:04:46.1897 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.1900 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.1909 { E } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] setPixmapNum(0) failed! defined pixmaps: []
12:04:46.1912 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.1920 { E } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] RemovePopup, id = ZapError
12:04:46.1922 [ ] dvb/dvbtime.cpp:700 DVBChannelStateChanged [eDVBLocalTimerHandler] remove channel 0x1557a80
12:04:46.1925 [ ] dvb/epgcache.cpp:728 DVBChannelStateChanged [EPGCache] remove channel 0x1557a80
12:04:46.1932 [ ] dvb/epgcache.cpp:2452 abortEPG [EPGCache] abort caching events !!
12:04:46.1966 [ ] dvb/dvb.cpp:1412 allocateChannel [eDVBResourceManager] allocate channel.. 2111:20cb
12:04:46.1967 [ ] dvb/dvb.cpp:1415 allocateChannel [eDVBResourceManager] available channel.. 0ca2:0003
12:04:46.1967 [ ] dvb/frontend.cpp:3661 isCompatibleWith m_dvbid:3 m_slotid:3 type:2 types:4 m_enabled:0
12:04:46.1967 [ ] dvb/frontend.cpp:3661 isCompatibleWith m_dvbid:4 m_slotid:4 type:2 types:4 m_enabled:0
12:04:46.1967 [ ] dvb/frontend.cpp:3661 isCompatibleWith m_dvbid:5 m_slotid:5 type:2 types:4 m_enabled:0
12:04:46.1968 [ ] dvb/frontend.cpp:3661 isCompatibleWith m_dvbid:6 m_slotid:6 type:2 types:4 m_enabled:0
12:04:46.1968 [ ] dvb/frontend.cpp:3661 isCompatibleWith m_dvbid:7 m_slotid:7 type:2 types:4 m_enabled:0
12:04:46.1977 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:04:46.1977 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:04:46.1979 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:04:46.1979 [ ] dvb/pmt.cpp:1057 tuneExt [eDVBServicePMTHandler] allocate Channel: res 0
12:04:46.1980 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=00
12:04:46.1980 [ ] dvb/dvb.cpp:1105 allocateDemux [eDVBResourceManager] allocate demux cap=00
12:04:46.1980 [ ] dvb/dvb.cpp:1281 allocateDemux [eDVBResourceManager] allocating demux adapter=0, demux=1, source=8
12:04:46.1980 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:04:46.2015 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] [Screen] Showing screen 'InfoBarSummary'.
12:04:46.2047 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:04:46.2095 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] [Screen] Showing screen 'InfoBar'.
12:04:46.2102 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:04:46.2283 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:04:46.2296 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:04:46.2298 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:04:46.2302 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:04:46.2302 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:04:46.2305 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:04:46.3544 [ ] driver/rcinput.cpp:38 handleCode [eRCDeviceInputDev] 0 160 1
12:04:46.3559 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:04:46+0100 [-] KEY: 352 1 KEY_OK OK
12:04:51.2293 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:04:51.2293 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:04:51.2294 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:04:51.2295 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:04:51.2296 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:04:51.2296 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:04:51.2299 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:04:51.2300 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:04:51.2300 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:04:51.2300 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:04:51.2301 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:04:51.2302 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:04:51.2302 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:04:51.2303 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:04:51.2305 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:04:51.2306 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:04:51.2306 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:04:56.2302 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:04:56.2303 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:04:56.2303 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:04:56.2305 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:04:56.2306 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:04:56.2306 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:04:56.2310 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:04:56.2310 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:04:56.2310 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:04:56.2311 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:04:56.2311 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:04:56.2312 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:04:56.2312 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:04:56.2313 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:04:56.2316 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:04:56.2316 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:04:56.2317 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:01.2312 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:01.2313 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:01.2313 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:01.2315 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:01.2316 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:01.2316 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:01.2320 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:01.2321 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:01.2321 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:01.2321 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:01.2322 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:01.2322 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:01.2323 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:01.2324 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:01.2326 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:01.2327 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:01.2327 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:05.8276 [ ] service/servicedvbrecord.cpp:566 gotNewEvent [eDVBServiceRecord] pcr of eit change: 165175a93
12:05:05.8277 [ ] service/servicedvbrecord.cpp:571 gotNewEvent [eDVBServiceRecord] now running: Babica vs. Sapík (3300 seconds)
12:05:05.8279 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux0
12:05:05.8280 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=18
12:05:06.2323 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:06.2323 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:06.2324 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:06.2326 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:06.2326 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:06.2327 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:06.2331 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:06.2331 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:06.2331 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:06.2332 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:06.2332 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:06.2333 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:06.2333 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:06.2334 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:06.2337 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:06.2337 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:06.2338 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:11.2333 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:11.2334 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:11.2334 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:11.2336 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:11.2337 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:11.2337 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:11.2341 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:11.2341 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:11.2342 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:11.2342 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:11.2343 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:11.2343 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:11.2344 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:11.2344 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:11.2347 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:11.2347 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:11.2348 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:16.2343 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:16.2344 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:16.2345 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:16.2347 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:16.2347 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:16.2348 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:16.2351 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:16.2352 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:16.2352 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:16.2353 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:16.2354 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:16.2354 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:16.2355 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:16.2356 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:16.2358 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:16.2359 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:16.2359 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:21.2355 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:21.2355 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:21.2355 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:21.2358 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:21.2358 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:21.2358 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:21.2362 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:21.2363 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:21.2363 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:21.2363 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:21.2364 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:21.2365 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:21.2365 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:21.2366 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:21.2368 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:21.2369 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:21.2369 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:26.2365 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:26.2366 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:26.2366 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:26.2368 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:26.2368 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:26.2369 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:26.2372 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:26.2373 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:26.2373 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:26.2374 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:26.2374 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:26.2375 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:26.2375 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:26.2376 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:26.2379 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:26.2379 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:26.2380 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:31.2375 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:31.2376 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:31.2376 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:31.2378 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:31.2379 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:31.2379 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:31.2383 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:31.2384 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:31.2384 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:31.2384 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:31.2385 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:31.2385 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:31.2386 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:31.2387 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:31.2389 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:31.2389 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:31.2390 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:36.2386 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:36.2386 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:36.2387 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:36.2389 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:36.2389 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:36.2389 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:36.2393 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:36.2394 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:36.2394 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:36.2394 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:36.2395 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:36.2395 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:36.2396 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:36.2397 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:36.2399 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:36.2399 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:36.2400 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:41.2396 [ E ] dvb/dvb.cpp:1917 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 failed, retune
12:05:41.2396 [ ] dvb/frontend.cpp:3226 tune tune tuner 8
12:05:41.2397 [ ] dvb/frontend.cpp:3185 prepare_terrestrial frontend 8 tuning dvb-t to 570000000 khz, bandwidth 8000000, modulation 3, inversion 2
12:05:41.2399 [ ] dvb/dvb.cpp:1893 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 tuning
12:05:41.2399 [ E ] dvb/pmt.cpp:116 channelStateChanged [eDVBServicePMTHandler] tune failed.
12:05:41.2400 [ E ] service/servicedvb.cpp:1207 serviceEvent [eDVBServicePlay] DVB service failed to tune - error 1
12:05:41.2404 [ ] dvb/pmt.cpp:1010 SDTScanEvent [eDVBServicePMTHandler] ignore sdt update data.... incorrect transponder tuned!!!
12:05:41.2404 [ ] dvb/pmt.cpp:1012 SDTScanEvent [eDVBServicePMTHandler] incorrect namespace. expected: eeee0000 current: ffffffff
12:05:41.2405 [ ] dvb/pmt.cpp:1014 SDTScanEvent [eDVBServicePMTHandler] incorrect transport_stream_id. expected: 2111 current: ffffffff
12:05:41.2405 [ ] dvb/pmt.cpp:1016 SDTScanEvent [eDVBServicePMTHandler] incorrect original_network_id. expected: 20cb current: ffffffff
12:05:41.2405 [ ] dvb/frontend.cpp:2640 tuneLoopInt [SEC] tuner 8 newTunertype 2
12:05:41.2406 [ ] dvb/frontend.cpp:2195 tuneLoopInt [SEC] tuner 8 startTuneTimeout 5000
12:05:41.2406 [ ] dvb/frontend.cpp:2093 tuneLoopInt [eDVBFrontend] [SEC] tuner 8 setVoltage 0
12:05:41.2407 [ ] dvb/frontend.cpp:3517 setVoltage [eDVBFrontend8] setVoltage FE_ENABLE_HIGH_LNB_VOLTAGE 0 FE_SET_VOLTAGE 2
12:05:41.2410 [ ] dvb/frontend.cpp:2188 tuneLoopInt [SEC] tuner 8 setFrontend: events enabled
12:05:41.2410 [ ] dvb/frontend.cpp:2668 setFrontend setting frontend 8 events: on
12:05:41.2411 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 0, inversion off, m_tuning 1
12:05:41.6405 [ ] dvb/frontend.cpp:1090 feEvent [eDVBFrontend] (8)fe event: status 1f, inversion off, m_tuning 2
12:05:41.6406 [ ] dvb/dvb.cpp:1889 frontendStateChanged [eDVBChannel] OURSTATE: tuner 8 ok
12:05:41.6406 [ ] dvb/dvbtime.cpp:684 DVBChannelStateChanged [eDVBLocalTimerHandler] channel 0x1557a80 running
12:05:41.6407 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=00
12:05:41.6407 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6408 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=20
12:05:41.6411 [ ] dvb/epgcache.cpp:722 DVBChannelStateChanged [EPGCache] channel 0x1557a80 running
12:05:41.6412 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=00
12:05:41.6412 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6413 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6413 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6413 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6414 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6414 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6415 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6415 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6415 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6416 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6416 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6416 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6417 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6417 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6418 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6418 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.6418 [ ] dvb/dvb.cpp:1491 DVBChannelStateChanged [eDVBResourceManager] stop release channel timer
12:05:41.6419 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=01
12:05:41.6419 [ ] dvb/dvb.cpp:1105 allocateDemux [eDVBResourceManager] allocate demux cap=01
12:05:41.6419 [ ] dvb/dvb.cpp:1214 allocateDemux [eDVBResourceManager] allocating shared demux adapter=0, demux=1, source=8
12:05:41.6419 [ ] dvb/pmt.cpp:78 channelStateChanged [eDVBServicePMTHandler] ok ... now we start!!
12:05:41.6420 [ ] service/servicedvb.cpp:1213 serviceEvent [eDVBServicePlay] eventNewProgramInfo timeshift_enabled=0 timeshift_active=0
12:05:41.6420 < > service/servicedvb.cpp:2912 updateDecoder [eDVBServicePlay] have 1 video stream(s) (083e), and 1 audio stream(s) (084a), and the pcr pid is 083e, and the text pid is 0852
12:05:41.6421 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=01
12:05:41.6424 [ ] dvb/epgcache.cpp:2430 startChannel [EPGCache] next update in 47 min
12:05:41.6443 [ ] service/servicedvb.cpp:3597 setAC3Delay [eDVBServicePlay] Setting audio delay: setAC3Delay, 0 + 0
12:05:41.6444 [ ] service/servicedvb.cpp:3608 setPCMDelay [eDVBServicePlay] Setting audio delay: setPCMDelay, 0 + 0
12:05:41.6445 [ ] dvb/decoder.cpp:870 setState [eTSMPEGDecoder] decoder state: play, vpid=083e, apid=084a
12:05:41.6445 < > dvb/decoder.cpp:741 startPid [eDVBPCR0] DMX_SET_PES_FILTER pid=0x083e ok
12:05:41.6446 < > dvb/decoder.cpp:749 startPid [eDVBPCR0] DEMUX_START ok
12:05:41.6488 < > dvb/decoder.cpp:84 startPid [eDVBAudio0] DMX_SET_PES_FILTER pid=0x084a ok
12:05:41.6488 < > dvb/decoder.cpp:92 startPid [eDVBAudio0] DEMUX_START ok
12:05:41.6489 < > dvb/decoder.cpp:142 startPid [eDVBAudio0] AUDIO_SET_BYPASS bypass=0 ok
12:05:41.6576 < > dvb/decoder.cpp:195 freeze [eDVBAudio0] AUDIO_PAUSE ok
12:05:41.6610 < > dvb/decoder.cpp:150 startPid [eDVBAudio0] AUDIO_PLAY ok
12:05:41.6675 [ ] dvb/decoder.cpp:269 eDVBVideo [eDVBVideo] Video Device: /dev/dvb/adapter0/video0
12:05:41.6676 [ ] dvb/decoder.cpp:280 eDVBVideo [eDVBVideo] demux device: /dev/dvb/adapter0/demux1
12:05:41.6720 < > dvb/decoder.cpp:360 startPid [eDVBVideo0] VIDEO_SET_STREAMTYPE 7 - ok
12:05:41.6762 < > dvb/decoder.cpp:395 startPid [eDVBVideo0] DMX_SET_PES_FILTER pid=0x083e ok
12:05:41.6763 < > dvb/decoder.cpp:403 startPid [eDVBVideo0] DEMUX_START ok
12:05:41.6764 < > dvb/decoder.cpp:464 freeze [eDVBVideo0] VIDEO_FREEZE ok
12:05:41.6800 < > dvb/decoder.cpp:418 startPid [eDVBVideo0] VIDEO_PLAY ok
12:05:41.6891 < > dvb/decoder.cpp:819 startPid [eDVBText0] DMX_SET_PES_FILTER pid=0x0852 ok
12:05:41.6891 < > dvb/decoder.cpp:827 startPid [eDVBText0] DEMUX_START ok
12:05:41.6910 < > dvb/decoder.cpp:488 setSlowMotion [eDVBVideo0] VIDEO_SLOWMOTION 0 ok
12:05:41.6956 < > dvb/decoder.cpp:503 setFastForward [eDVBVideo0] VIDEO_FAST_FORWARD 0 ok
12:05:41.7003 < > dvb/decoder.cpp:476 unfreeze [eDVBVideo0] VIDEO_CONTINUE ok
12:05:41.7042 < > dvb/decoder.cpp:207 unfreeze [eDVBAudio0] AUDIO_CONTINUE ok
12:05:41.7127 [ ] dvb/teletext.cpp:222 eDVBTeletextParser [eDVBTeletextParser] Starting!
12:05:41.7127 [ ] dvb/teletext.cpp:645 setPageAndMagazine [eDVBTeletextParser] disable teletext subtitles page ffffffffffffffff (und)
12:05:41.7127 [!W!] dvb/demux.cpp:361 eDVBPESReader [eDVBPESReader] Created. Opening demux
12:05:41.7127 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.7128 [ ] dvb/teletext.cpp:230 eDVBTeletextParser [eDVBTeletextParser] created teletext subtitle PES reader!
12:05:41.7129 [!W!] dvb/demux.cpp:361 eDVBPESReader [eDVBPESReader] Created. Opening demux
12:05:41.7129 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.7130 [ ] dvb/teletext.cpp:463 start [eDVBTeletextParser] starting PES reader on pid=0852
12:05:41.7130 [ ] dvb/demux.cpp:399 start [eDVBPESReader] DMX_SET_PES_FILTER pid=0852
12:05:41.7136 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:41.7139 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:41.7141 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:41.7155 { E } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] setPixmapNum(0) failed! defined pixmaps: []
12:05:41.7159 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:41.7334 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] [Volume Adjust] Update Info
12:05:41.7339 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] [Volume Adjust] Volume = 100
12:05:41.7344 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] [Volume Adjust] load xml...
12:05:41.7352 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] [Volume Adjust] New Channel
12:05:41.7357 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] [Volume Adjust] oldvol = 0
12:05:41.7390 [ ] dvb/cahandler.cpp:267 registerService [eDVBCAService] new service 1:0:1F:10C:2111:20CB:EEEE0000:0:0:0::CT 1 HD T
12:05:41.7390 [ ] dvb/cahandler.cpp:285 registerService [eDVBCAService] add demux 1 to slot 0 service 1:0:1F:10C:2111:20CB:EEEE0000:0:0:0::CT 1 HD T
12:05:41.7397 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.7398 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=0
12:05:41.7473 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:41.7605 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.7605 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=18
12:05:41.7627 { E } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:41+0100 [-] RemovePopup, id = ZapError
12:05:41.7629 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:41.7629 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=0
12:05:42.0743 [ ] dvb/pmt.cpp:215 PATready [eDVBServicePMTHandler] PATready
12:05:42.0744 [ ] dvb/pmt.cpp:226 PATready [eDVBServicePMTHandler] PAT TSID: 0x2111 (8465)
12:05:42.0744 [ ] dvb/pmt.cpp:255 PATready [eDVBServicePMTHandler] use pmtpid 0834 for service_id 010c
12:05:42.0744 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.0745 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2100
12:05:42.0748 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.0749 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=0
12:05:42.0760 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.0761 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2100
12:05:42.0767 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.0767 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=17
12:05:42.2018 [ ] service/servicedvb.cpp:1213 serviceEvent [eDVBServicePlay] eventNewProgramInfo timeshift_enabled=0 timeshift_active=0
12:05:42.2022 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.2022 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2160
12:05:42.2028 < > service/servicedvb.cpp:2912 updateDecoder [eDVBServicePlay] have 1 video stream(s) (083e), and 4 audio stream(s) (0848, 0849, 084a, 084b), and the pcr pid is 083e, and the text pid is 0852
12:05:42.2030 [ ] service/servicedvb.cpp:3597 setAC3Delay [eDVBServicePlay] Setting audio delay: setAC3Delay, 0 + 0
12:05:42.2031 [ ] service/servicedvb.cpp:3608 setPCMDelay [eDVBServicePlay] Setting audio delay: setPCMDelay, 0 + 0
12:05:42.2031 [ ] dvb/decoder.cpp:870 setState [eTSMPEGDecoder] decoder state: play, vpid=083e, apid=084a
12:05:42.2044 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.2045 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2160
12:05:42.2104 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:42+0100 [-] [Volume Adjust] Update Info
12:05:42.2110 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:42+0100 [-] [Volume Adjust] Volume = 100
12:05:42.2117 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:42+0100 [-] [Volume Adjust] load xml...
12:05:42.2154 [ ] dvb/cahandler.cpp:624 buildCAPMT [eDVBCAService] don't build/send the same CA PMT twice
12:05:42.2157 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.2157 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2100
12:05:42.2171 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.2171 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2200
12:05:42.3359 [ ] dvb/pmt.cpp:301 AITready [eDVBServicePMTHandler] AITready
12:05:42.3359 [ ] dvb/pmt.cpp:320 AITready [eDVBServicePMTHandler] Section Length : 102, Total Section Length : 105
12:05:42.3360 [ ] dvb/pmt.cpp:331 AITready [eDVBServicePMTHandler] found applicaions ids >> pid : 0, orgid : 400, appid : 1
12:05:42.3362 [ ] dvb/pmt.cpp:295 saveData [eDVBServicePMTHandler] Save Data Len : [105]
12:05:42.3362 [ ] dvb/pmt.cpp:465 AITready [eDVBServicePMTHandler] Found : control[1], name[CT-start], url[http://hbbtv.ceskatelevize.cz/start/index.html]
12:05:42.3411 { } /usr/lib/python2.7/site-packages/twisted/python/util.py:815 untilConcludes 2021-03-27 12:05:42+0100 [-] (1, 'CT-start', 'http://hbbtv.ceskatelevize.cz/start/index.html', 400, 1, 0)
12:05:42.4382 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.4383 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=18
12:05:42.4389 [ ] dvb/dvbtime.cpp:471 updateTime [eDVBLocalTimerHandler] Transponder time is 27.03.2021 12:05:42
12:05:42.4390 [ ] dvb/dvbtime.cpp:490 updateTime [eDVBLocalTimerHandler] diff is 0
12:05:42.4390 [ ] dvb/dvbtime.cpp:493 updateTime [eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
12:05:42.4391 [ ] dvb/dvbtime.cpp:554 updateTime [eDVBLocalTimerHandler] not changed
12:05:42.4399 [ ] dvb/dvb.cpp:2421 getDemux [eDVBChannel] getDemux cap=00
12:05:42.4635 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.4636 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2300
12:05:42.5764 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.5765 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2400
12:05:42.6012 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.6013 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2500
12:05:42.7354 < > dvb/decoder.cpp:547 video_event [eDVBVideo0] VIDEO_GET_EVENT SIZE_CHANGED 1920x1080 aspect 3
12:05:42.7475 [ ] service/servicedvb.cpp:1747 timeshift [eDVBServicePlay] timeshift
12:05:42.7516 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:42.7517 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2600
12:05:43.0630 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:43.0631 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2700
12:05:43.3760 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:43.3761 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=2800
12:05:43.4759 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:05:43.4760 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=7010
12:05:43.5119 [ ] dvb/pmt.cpp:1006 SDTScanEvent [eDVBServicePMTHandler] sdt update done!
12:06:20.8323 [ ] dvb/demux.cpp:90 openDemux [eDVBDemux] open demux /dev/dvb/adapter0/demux1
12:06:20.8324 [ ] dvb/demux.cpp:286 start [eDVBSectionReader] DMX_SET_FILTER pid=18
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 13:45
od VTronik
V image bych chybu nehledal. Používám ho také a žádné problémy při přepínání neeviduji. Spíše bych se zaměřil na to, jak daleko máš od místa příjmu vysílače Buková Hora a Jedlová hora. Jedou v SFN a při nevhodné konstalaci signálu a vzdáleností mohou nastat potíže. Je to potom i záležitost antény a její směrovosti.
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 14:08
od hrotik
Přikláním se k názoru VTronika, v tom SFN se to může mydlit mezi sebou. Nejrychlejší prověření - připojit box na jinou anténní sestavu u souseda,kamaráda,známého.
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 20:05
od dipol100
Jedlová hora je moc daleko a na anténu je z boku. Divný je, že neblbnou ostatní MUXy. Je to už třetí DUO4K za poslední měsíc, který mám. První na DVB-S2 samo přepínalo DiSEqC mezi 23,5 a 19,2. Druhé nahrávalo ze SAT většinou tmu. Tento perfektně nahrává ze SAT, ale zase má problém se signálem na DVB-T2. Ve všech byl stejný OATV6.4 obnovený ze stejné flasky. Evidentně je ta kvalita VU+ dost mizerná. Vedle něj stojí GigaBlue a nemá se signálem problém, stejně jako v patře AMIKO a 3x TV LG a 1x PHILIPS, navíc mám pro jistotu všude filtr 5G. Teď jsem tam měl i VTi a tma v jednu chvíli trvalo přepnutí na ČT1 2,5 minuty!
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 20:48
od VTronik
Ze tvé odpovědi nepozná nikdo nic. Zase jen domněnky o špatné kvalitě VU... Netvrdím, že nemůžeš mít smůlu, ale těch náhod je na můj vkus u tebe až podezřele mnoho. Odpověď, že Jedlová hora je daleko vůbec nic neřeší a hlavně neříká. To, že fungují jiné MUXy také nic neznamená. Filtr LTE s tím nemá také nic společného, pokud vyloučím možné přebuzení zesilovače signálem mimo aktuální TV pásmo. Řešíš příjem na K33 v SFN a k tomu je potřeba zjistit údaje. Odpověděl jsem ti hlavně proto, že s příjmem v SFN DVB-T2 na K33 u VU Duo 4K SE a image OATV 6.4 žádný problém není. Ale vím o tom, že v SFN mezi vysílači Jedlová hora a Buková hora se na některých místech problém vyskytuje. Záleží skutečně na konkrétním místě a jak se tam signál na anténě schází. Různé tunery se s tím perou různě a neznamená to, že je některý vadný. Je jen jinak citlivý na určitou konstalaci signálu. Ideální je v takovém případě změřit impulsní odezvu (echo, preecho a jejich úrovně) vysílačů na K33, jaký je signál přímo z antény. Ani bych se nedivil, pokud máš na svodu problém úplně jiný, protože ten DiSEqC jak si to popisoval byl také zcela unikátní problém... Samovolné přepínání jsem snad ještě nikde neviděl. Jak si to nakonec vyřešil jsme se ale nedozvěděli.
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 20:54
od hrotik
Tak flešnout poslední VTI, které je primárně pro vu+ určené. Že by to VU+ tak hluboko kleslo...?
VTronik
Re: Veli pomale prepinanie medzi programami
Napsal: 27.březen 2021 - 21:49
od dipol100
Vždy jsem měl vedle sebe dva přijímače DUO4K, jak u problému s DiSEqC, tak při problému s nahráváním tmy přes SAT, na obou přijímačích vždy obnovená stejná image, vždy jsem prohodil i přívod elektřiny i anténní a sat. vstupy a chyba byla vždy jen na tom stejném, nikdy se stejný problém neprojevil na druhém přijímači, takže selským rozumem to musí být problém na přijímači. Bohužel jsem řešil DVB-S2, pak jsem vadný přijímač s problémem tmy vrátil a zjistil, že tento má sice OK DVB-S2, ale zase má problém s DVB-T2. Ten první s problémem DiSEqC, tam jsem testoval DVB-T2 hodně a bylo vše v pořádku, takže jsem se na to u dalších přijímačů už nezaměřoval. Mě i trpaslík vyroste... .Co se týká antény, měl jsem tu kvůli podezření na rušení LTE ČTÚ, vše proměřili a prý tak bezvadnou soustavu ještě neviděli....